1998 toyota corolla owners manual free download

If the booster battery is installed in Discharged battery Jumper cable another vehicle, make sure the vehicles are not touching. Turn off all unneces- sary lights and accessories. If required, remove all the vent plugs Booster battery from the booster and discharged batter- ies. Start your engine in the normal way. If your engine stalls while driving Connecting point After starting, run it at about rpm 1. Reduce your speed gradually, keeping for several minutes with the accelerator a straight line.

Page You should have it checked as soon as possible at your Toyota dealer. Pull safely off the road, stop the ve- hicle and Get the required tools and spare tire. Vehicles with compact spare tire 1. Spare tire 2. Jack handle 3. Jack 4. Wheel nut wrench Vehicles without compact spare tire 1. Block the wheel diagonally opposite the flat tire to keep the vehicle from 1. Raise the luggage compartment floor. Remove the wheel ornament. Pry off the wheel ornament, using the beveled end of the wheel nut wrench as shown.

Take due care in handling the ornament to avoid unexpected person- al injury. After making sure that no one is in 7. Remove the wheel nuts and change the vehicle, raise it high enough so tires.

Reinstall all the wheel nuts finger 9. Lower the vehicle completely and rosion on the mounting surfaces with a tight. Reinstall the wheel ornament. Put the wheel ornament into position. When lowering the vehicle, make sure On some models, align the cutout of the wheel ornament with the valve stem as all portions of your body and all oth- shown.

Page Check the air pressure of the re- If towing is necessary, we recommend placed tire. Use a towing dolly under the front wheels. Page The eyelets and towing cable If towing is necessary, we recommend or chain may break and cause serious you to have it done by your Toyota injury or damage. Proper " High temperatures will cause corrosion care of your Toyota can help ensure long- to those components of the vehicle " Protecting your Toyota from term corrosion prevention.

Begin by vacuuming thoroughly to remove Be careful not to splash water or First vacuum over the upholstery to re- as much dirt as possible. Page Immediately clean any spill using the method mentioned above. If you have any questions about the cleaning of your Toyota, your local Toyota dealer will be pleased to answer them. Warranty Booklet for complete warranty information. Page They learn to work on for the details.

It is recom- rather than while they are working on it. See Chapter 7- 2 for lights, turn signal lights, and other lights uneven pedal effort or catching. It probably needs adjustment or repair. It could result in se- rious vehicle damage and possibly personal injury. Power steering fluid reservoir 2. Engine oil level dipstick 3. Engine oil filler cap 4. Brake fluid reservoir 5. Fuse blocks 6. Battery 7. Engine coolant reservoir 8.

Electric cooling fans 9. Windshield washer fluid tank Page Toyota Warranty statement for details and exhaust manifold and spark plug where you may be exposed to flying suggestions. So be or falling material, fluid spray, etc.

Page Remember all Toyota parts are de- could be damaged. Do not dispose of used oil and fil- signed in metric sizes, so your tools must ter in household trash, in sewers or z Do not drive with the air cleaner be metric.

Page Do not use alcohol type antifreeze or plain water alone. If you can find no leak, have your Toyota dealer test the cap pressure and check for leaks in the cooling system. Once the see- through reservoir. Page If a tire frequently needs refilling, have it Keep your tire pressures at the proper checked by your Toyota dealer. Page When rotating tires, check for uneven mended size.

Abnormal wear is usu- ally caused by incorrect tire pressure, im- Toyota recommends all four tires, or at proper wheel alignment, out- of- balance least both of the front or rear tires be Vehicles with compact spare tire wheels, or severe braking. Drive carefully avoiding bumps, type. When replacing wheels, care should be Use only the Toyota wheel nuts and taken to ensure that the wheels are re- wrench designed for your aluminum placed by ones with the same load ca- wheels.

The battery produces flammable and " Charging necessary. If the terminal connections are loose, by your Toyota dealer. Have battery checked c. Tighten hold- down clamp only by your Toyota dealer. Therefore, before recharging: Type A 1. If recharging with the battery installed on the vehicle, be sure to disconnect the ground cable.

Page Have your Toyota dealer correct it as light comes on, the washer tank may be soon as possible. Add washer fluid.

Use bulbs with the Parking, front side wattage ratings given in the table. Unplug the connector. Remove the driver or equivalent clip and take out the air cleaner rubber cover. If the connector is tight, wiggle it. Remove and install the cover clip as shown in the following illustration. Page Make sure the rubber cover fits snugly on bulb with the cutouts of the mounting the connector and the headlight body.

Aiming is not necessary after replacing the bulb. Toyota service manuals are readily downloadable from this site and will aid any driver with diagnosis and solutions to the rare problems that occur with Toyota cars. You could possibly need to know in order to ensure that you are fully informed when it comes to keeping your Toyota car on the road. The download is free, too, which will save. Download a toyota corolla repair manual straight to your computer in just seconds.

Fix your problems now! Toyota Owner manuals and warranty information are the keys to quality maintenance for your vehicle. No need to hunt down a separate Toyota repair manual or Toyota service manual. From warranties on Toyota replacement parts to details on features, Toyota Owners manuals help you find everything you need to know about your vehicle, all in one place.

Detailed Toyota manuals and Toyota warranty information help with questions about your vehicle specifications and maintenance schedules.

Plus, learn more about what your Toyota warranty coverage includes. SRS airbag warning light 2. Side airbag module airbag and inflator 3. Side airbag sensor assembly 4. Airbag sensor assembly Deployment of the airbags happen in a fraction of a second, so the airbags must inflate with considerable force. Front seats may be hot for several minutes, but the airbags themselves will not be hot. The SRS side airbag system is controlled by the airbag sensor. During sudden braking just before a collision, an unrestrained driver or front passenger can move sideward into direct contact with or close proximity to the airbag which may then deploy during the collision.

D Do not allow the child to lean against the front door even if the child is seated in the child restraint system. It is dangerous if the side airbag inflates and the impact could cause death or serious injury to the child.

The side airbag inflates with considerable speed and force; you may be killed or be seriously injured. D Do not apply excessive weight to the outer side of the front seats on vehicles with side airbags. D The child head should not be leaned against the vicinity of the part where the side airbag activates. Such accessories may prevent the side airbags from activating correctly, causing serious injury. D Do not attach a cup holder or any other device on or around the door. When the side airbag inflates, the cup holder or any other device will be thrown with great force or the side airbag may not activate correctly, resulting in death or serious injury.

The laws of all fifty states in the U. Your vehicle conforms to SAE J This SRS side airbag system has a service reminder indicator to inform the driver of operating problems.

D The light comes on or flashes while driving. D The portion of the doors shaded in the illustration were involved in an accident that did not cause the SRS side airbags to inflate. D The surface of the seats with the side airbag shaded in the illustration is scratched, cracked, or otherwise damaged. Holding a child in your arms is not a substitute for a child restraint system.

On vehicles with side airbags, do not allow the child to lean against the front door or around the front door even if the child is seated in the child restraint system. D Make sure that you have complied with all installation instructions provided by the child restraint manufacturer and that the system is properly secured. Install the child restraint system correctly following the instructions provided by its manufacturer of the system.

Toyota recommends installing the child restraint system on the rear seat. If it is not restrained securely, it may cause death or serious injury to the child in the event of a sudden stop or accident. When not using the child restraint system, keep it secured with the seat belt or place it in the trunk or somewhere other than the passenger compartment.

This will prevent it from injuring passengers in the event of a sudden stop or accident. Your vehicle has anchors for securing the top strap of a child restraint system. The anchor nuts are welded beneath the sheet metal to permit installation of an anchor bracket for a child restraint system. To install an anchor bracket, use an 8 mm 30 mm 1. Note that the bolts accompanying many child restraint systems are not metric. You can damage the anchor nuts on your vehicle if you force bolts with different thread into the anchor nuts.

If your child restraint system does not provide any of the necessary parts, you can purchase the following items from your Toyota dealer. Refer to the illustration to become familiar with the parts of the system. This child restraint system conforms to U. Motor Vehicle Safety Standard No. Head restraint lock release button 2. Shoulder pads 3. Shoulder belts 4.

Head restraint 5. Maximum shoulder height indicator label 6. Removable pad 7. Seat belt buckle 8. Seat belt release strap black 9. Seat belt adjustment strap gray tab Child seat cushion Seat belt buckle release button Seat belt tabs The child should be at least one year old and must be capable of sitting upright alone and whose shoulder height is at or below the maximum shoulder height indicator.

According to accident statistics, children are safer when properly restrained in the rear seat than in the front seat. Snugly adjust the belts provided with this child restraint around your child. Do not use the belts for two or more children. Take care that they do not get caught or pinched in the seatback.

Do not disassemble or modify the child restraint belt system. Separate the fastener tapes under the right rear seatback and fold the separated part of the seatback down while lowering it. Unlock and remove the head restraint, then reinstall it facing backward. While pulling the seat belt release strap black , pull both shoulder belts together.

If the shoulder belts cannot be pulled out, return the child seat cushion to an almost closed position, firmly pull the seat belt release strap and at the same time pull both shoulder belts, then lower the child seat cushion again. Compress the shoulder belt clip to separate the right and left shoulder belts. Pull down the seatback part of the removable pad. Press the removable pad against the fastener tapes and install the pad to the seatback.

Make sure the belts go through the slots in the pad. The removable pad is attached by fastener tapes. Your child should use the adult lap and shoulder belt. D If the seat belt does not function normally, it cannot protect your child from injury.

Contact your Toyota dealer immediately. Sit the child on the child seat. Place a shoulder belt over each shoulder. Insert the tabs into the buckle. Adjust the shoulder pads. D After inserting the tabs, make sure the tabs and buckle are locked and that the shoulder belts and buckle strap are not twisted.

Fasten the shoulder belt clip. The purpose of the clip is to keep the shoulder belts positioned correctly on the shoulders. In a sudden stop or crash, the child may go too far forward and be seriously injured. Make sure the belt clip is fastened at all times.

After adjusting the shoulder belt tightness, move the shoulder belt clip 5 to 8 cm 2 to 3 in. To release the child from the seat belts, separate the shoulder belts then press the buckle release button. A Infant seat B Convertible seat C Booster seat Install the child restraint system following the instructions provided by its manufacturer. Fold up the seat belt adjustment strap gray tab in the seat so that the edge of the strap does not come out the raised child restraint cushion.

Raise the child restraint cushion and reinstall the head restraint correctly by inserting the posts into the holes.

Do not occupy this position unless the head restraint is reinstalled as serious injury may result. This can cause severe injury to the child and front passenger in case of sudden braking or a collision.

Run the lap and shoulder belt through or around the infant seat following the instructions provided by its manufacturer and insert the tab into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended. To hold the infant seat securely, make sure the belt is in the lock mode before letting the belt retract. While pressing against the seat let the shoulder it will go to hold ly.

Follow all the installation instructions provided by its manufacturer. The belt will move freely again and be ready to work for an adult or older child passenger. D If the seat belt does not function 1. Run the lap and shoulder belt through or around the convertible seat following the instructions provided by its manufacturer and insert the tab into the buckle taking care not to twist the belt. To hold the convertible seat securely, make sure the belt is in the lock mode before letting the belt retract.

While pressing the convertible seat firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the convertible seat securely. Failure to do so could reduce the amount of protection in an accident and cause serious injuries in a collision. Sit the child on a booster seat. Run the lap and shoulder belt through or around the booster seat and child following the instructions provided by its manufacturer and insert the tab into the buckle taking care not to twist the belt.

Keep the lap belt as low on hips as possible. D After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted. Spacer If your child restraint system requires the use of a top strap, latch the hook onto the anchor bracket and tighten the top strap. See the following instructions to install the anchor bracket. On the filler panel behind the rear seat a. Using the illustration as a guide, run your fingers across the trim of the filler panel itself to locate the position of the holes underneath.

Make a hole in the covering directly above the hole in the filler panel. Insert a 15 mm 0. Torque the bolt to Adjust the mirror so you can see the side of your vehicle in the mirror. To comply with Canada Motor Vehicle Safety Standards, vehicles sold in Canada are provided with a bracket set in the glovebox, designed for use with any of the 3 anchor locations shown in the illustration.

If your child restraint system does not provide any of the necessary parts, ask your Toyota dealer. When the steering wheel is in a low position, it will spring up as you release the lock release lever. D After adjusting the steering wheel, try moving it up and down to make sure it is locked in position. It is a convex mirror with a curved surface. Any object seen in a convex mirror will look smaller and farther away than when seen in a flat mirror.

It may cause the driver to mishandle the vehicle and an accident may occur resulting in personal injuries. To adjust the rear view mirror, simply operate the control lever. To adjust a mirror, use the switches. Control switch—To move the mirush the switch in the desired direcror P tion. Daylight driving—Lever at position 1 The reflection in the mirror has greater clarity at this position.

Night driving—Lever at position 2 Remember that by reducing glare you also lose some rear view clarity.

They will not go off until the ignition switch is turned off. To turn on the other exterior lights and instrument panel lights, twist the knob to the position 1. Twist the knob to the position 2 to turn the headlights to full intensity for driving at night. Vehicles for the U. Pull the lever toward you position 2 for low beams.

Flashing the high position 3 —Pull the back. The high beam when you release the beam headlights lever all the way headlights turn off lever. The lever automatically returns after you make a turn, but you may have to return it by hand after you change lanes.

To signal a lane change, move the lever up or down to the pressure point position 2 and hold it. If the turn signal indicator lights green lights on the instrument panel flash faster than normal, a front or rear turn signal bulb is burned out. To turn on the push the switch. To turn them off, push the switch once again. Turn on the emergency flashers to warn other drivers if your vehicle must be stopped where it might be a traffic hazard. Always pull as far off the road as possible. The turn signal light switch will not work when the emergency flashers are operating.

To turn on the interior light, slide the switch. NOTICE To prevent the battery from being discharged, do not leave the switch on longer than necessary when the engine is not running. The light remains on for a certain time after all the doors are closed. To turn on the personal light, push the switch.

To turn it off, push the switch once again. Windshield wipers and washer Type A The light remains on for a certain time after all the doors are closed. To squirt washer fluid, pull the lever toward you. With interval adjuster: If the windshield wipers are off, they will operate a couple of times after the washer squirts.

Twist the band upward to increase the time between sweeps, and downward to decrease it. In freezing weather, warm the windshield with the defroster before using the washer. This will help prevent the washer fluid from freezing on your windshield, which can block your vision. It may scratch the glass. To defog or defrost the rear window, push the switch. The thin heater wires on the inside of the rear window will quickly clear the surfaces. An indicator light will illuminate to indicate the defogger is operating.

Push the switch once again to turn the defogger off. On some models, the system will automatically shut off after the defogger has operated about 15 minutes. The defogger is not designed for drying rain water or for melting snow. To free it, first be sure the key is pushed all the way in, and then rock the steering wheel slightly while turning the key gently. For starting tips, see Part 3.

This is the normal driving position. The key can be removed only at this position. For manual transmission: Never remove the key when the vehicle is moving, as this will lock the steering wheel and result in loss of steering control. The battery will discharge and the ignition could be damaged. Shift while holding the lock release button in. Shift normally. Release the parking brake and brake pedal.

Depress the accelerator pedal slowly for smooth starting. The transmission will downshift to the second gear and more engine braking will be obtained. The transmission will downshift to the first gear and maximum engine braking will be applied. Abrupt shifting could cause the vehicle to spin or skid. Watch the tachometer to keep engine rpm from going into the red zone.

This may cause severe automatic transmission damage from overheating. Bring the vehicle to a complete stop. Pull the parking brake lever up fully to securely apply the parking brake. Serious mechanical damage and loss of vehicle control may result. This prevents the vehicle from creeping. It can cause the transmission to overheat. Always use the brake pedal or parking brake. During the rocking operation the vehicle may suddenly move forward or backward as it becomes unstuck, causing injury or damage to nearby people or objects.

NOTICE If your rock your vehicle, observe the following precautions to prevent damage to the transmission and other parts. Always turn the overdrive switch on for better fuel economy and quieter driving. If the engine coolant temperature is low, the transmission will not shift into overdrive gear even with the overdrive switch on. Be sure to turn the switch on immediately afterward. D When towing a trailer, in order to main- tain engine braking efficiency, do not use overdrive.

Press the clutch pedal down fully while shifting, and then release it slowly. Do not rest your foot on the pedal while driving, because it will cause clutch trouble. And do not use the clutch to hold the vehicle when stopped on an uphill grade—use the parking brake.

High altitude —Higher than m ft. Upshifting too soon or downshifting too late will cause lugging, and possibly pinging. Regularly revving the engine to maximum speed in each gear will cause excessive engine wear and high fuel consumption.

Maximum allowable speeds To get on a highway or to pass slower traffic, maximum acceleration may be necessary. D When towing a trailer, in order to main- tain engine braking efficiency, do not use the fifth gear. To set: Pull up the lever. For better holding power, first depress the brake pedal and hold it while setting the brake. To release: Pull up the lever slightly, press the thumb button, and lower. To remind you that the parking brake is set, the parking brake reminder light in the instrument panel remains on until you release the parking brake.

Your cruising speed can be maintained up or down grades within the limits of engine performance, although a slight speed change may occur when driving up or down the grades. On steeper hills, a greater speed change will occur so it is better to drive without the cruise control. D Avoid vehicle speed increases when driving downhill. If the vehicle speed is too fast in relation to the cruise control set speed, cancel the cruise control then downshift the transmission to use engine braking to slow down.

This turns the system on. The indicator light in the instrument panel shows that you can now set the vehicle at a desired cruising speed.

Another press will turn the system completely off. When you release it, the vehicle will return to the speed set prior to the acceleration. This sets the vehicle at that speed. If the speed is not satisfactory, tap the lever up for a faster speed, or tap it down for a slower speed. Each tap changes the set speed by 1.

You can now take your foot off the accelerator pedal. While driving with the cruise control on, do not shift to neutral without depressing the clutch pedal, as this may cause engine racing or overrevving. Depressing the brake pedal. Depressing the clutch pedal manual transmission.

If the preset speed automatically cancels out other than for the above cases, have your vehicle checked by your Toyota dealer at the earliest opportunity. Release the lever when the desired speed is attained. While the lever is held up, the vehicle will gradually gain speed. While the lever is held down, the vehicle speed will gradually decrease. To decrease the vehicle speed, reset to a slower speed with the cruise control lever or depress the brake pedal.

If you use the brake pedal, cruise control is cancelled. If any of the following conditions then occurs, there is some trouble in the cruise control system. D The indicator light flashes again. D The indicator light goes out after it comes on. If this is the case, contact your Toyota dealer and have your vehicle inspected.

Some information may not pertain to your system. You can turn on each player by inserting a cassette tape or compact disc. You can turn off each player by ejecting the cassette tape or compact disc. If the audio system was previously off, then the entire audio system will be turned off when you eject the cassette tape or compact disc.

If the another function was previously playing, it will come on again. In fact, different kinds of music and vocal programs usually sound better with different mixes of treble and bass. Balance A good balance of the left and right stereo channels and of the front and rear sound levels is also important.

NOTICE Do not oil any part of the player and do not insert anything other than cassette tapes into the slot, or the tape player may be damaged. The player will automatically eject a disc if the label side is down. The compact disc player will play from track 1 through the end of the disc. Then it will play from track 1 again. Do not insert anything except a compact disc into the slot. Compact disc singles are about 8 cm 3 in. After you eject a compact disc single, do not insert a standard 12 cm 5 in.

If the signal becomes weak, the radio reduces the amount of channel separation to prevent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono reception. The button number will appear on the display.

To tune in to a preset station: Push the button for the station you want. The button number and station frequency will appear on the display. These systems can store one AM and one FM station for each button. The preset station memory will be canceled out if the power source is interrupted battery disconnected or fuse blown. Eject button Push this button to eject a cassette.

This is true whether the cassette was playing or fast forwarding. In both cases, a cassette must already be loaded in the player. If a tape side rewinds completely, the cassette player will stop and then play that same side. If you hear a beep, you held the button too long and the radio will go into the seek mode. Seeking In the seek mode, the radio finds and plays the next station up or down the station band.

Do this again to find another station. Push the reverse button to rewind a tape. Push this button to eject a cassette. If you want to fast forward or reverse through a compact disc track, push and hold in the fast forward or reverse button.